Introduction:
Using serial console setup users can get access to the serial console of their router. Serial console setup finds its most important use in debricking a router. Moreover, developers may use it to extract useful debug information from their routers.
This short tutorial explains how to setup serial console for Netgear R6200v2.
Identify location of Serial pins on your router:
First open the case of your router. You should be able to find pins for serial communications at the location indicated in Figure1(a).
![]()
Figure1(a): Serial pin location on your router
Note:-
Some R6200v2 may not come with pins for serial communications. In such cases, you will have to attach the pins on your own. Go to the location as indicated in Figure1(a), where you will find a connection with the name J252 as shown in Figure 1(b). Solder the pins here carefully.
![]()
Figure1(b): Serial pin location on your router
Identify important pins on router for serial communication:
Important pins on the router for serial communication are identified in Figure 2.
![]()
Figure 2: Important pins on the router for serial communication
Identify important pins in USB-TTL cable:
Important pins in the USB-TTL cable are indicated in Figure 3.
![]()
Figure 3: Important pins in USB-TTL cable
How to connect USB-TTL cable to the pins on the router for serial communication:
The connection between USB-TTL cable and pins on the router for serial communication is explained in Figure 4.
![]()
Figure 4: Connection between USB-TTL cable and pins for serial communication
Physical setup of your serial console ends here.
Verification of the setup:
To verify your setup, start serial client on your PC with proper parameters and then power on your router. As soon as you do this, you will be able to see debug information from the router on your screen. If you do not see anything, check that all the connections have been made properly and if in doubt, reattach the cables. Verify that the Serial Client has the proper parameters for the connection.
Hopefully you will never have to refer to this tutorial, but for people who like to play with their routers, it sometimes happens -- you accidentally "brick" your router. This tutorial enables you to recover your router by flashing stock firmware back again using serial console and windows PC. Developers who want to get access to their router by using a serial console may also refer to this tutorial. Prerequisites:- Target router with serial connection pins on board. One Ethernet straight cable. An appropriate screwdriver, which is used to open the case of the router. A USB-TTL cable or compatible serial cable. A windows machine installed with following software, - TFTP Client. - Serial Client (preferably Putty. Which can be downloaded here ). - Appropriate driver software for your USB serial cable. Supported Netgear Router Models:- This tutorial may be referenced for following router models. R6200v1 R6200v2 Connect serial cable to your router:- This is very first step in the process. Connect USB end of the serial cable to your windows PC and other end to the serial pins on the board. Visit appropriate link below to get details of the serial pin connection for your router model. R6200v1 R6200v2...
Introduction: Using serial console setup users can get access to the serial console of their router. Serial console setup finds its most important use in debricking a router. Moreover, developers may use it to extract useful debug information from their routers. This short tutorial explains how to setup serial console for Netgear R7000. Identify location of Serial pins on your router: First open the case of your router. You should be able to find pins for serial communications at the location indicated in Figure1(a). Figure1(a): Serial pin location on your router Note:- Some R7000 may not come with pins for serial communications . In such cases, you will have to attach the pins on your own. Go to the location as indicated in Figure1(a), where you will find a connection with the name J252 as shown in Figure 1(b). Solder the pins here carefully. Figure 1(b): Serial pin location on your router Identify important pins on router for serial communication: Important pins on the router for serial communication are identified in Figure 2. Figure 2: Important pins on the router for serial communication Identify important pins in USB-TTL cable: Important pins in the USB-TTL cable are indicated in Figure 3....
Introduction: Using serial console setup users can get access to the serial console of their router. Serial console setup finds its most important use in debricking a router. Moreover, developers may use it to extract useful debug information from their routers. This short tutorial explains how to setup serial console for Netgear WNDR4500v1. Identify location of Serial pins on your router: First open the case of your router. You should be able to find pins for serial communications at the location indicated in Figure1(a). Figure1(a): Serial pin location on your router Note:- Some WNDR4500v1 may not come with pins for serial communications . In such cases, you will have to attach the pins on your own. Go to the location as indicated in Figure1(a), where you will find a connection with the name J252 as shown in Figure 1(b). Solder the pins here carefully. Figure1(b): Serial pin location on your router Identify important pins on router for serial communication: Important pins on the router for serial communication are identified in Figure 2. Figure 2: Important pins on the router for serial communication Identify important pins in USB-TTL cable: Important pins in the USB-TTL cable are indicated in Figure 3. Figure...
Introduction: Using serial console setup users can get access to the serial console of their router. Serial console setup finds its most important use in debricking a router. Moreover, developers may use it to extract useful debug information from their routers. This short tutorial explains how to setup serial console for Netgear WNDR4500v2. Identify location of Serial pins on your router: First open the case of your router. You should be able to find pins for serial communications at the location indicated in Figure1(a). Figure1(a): Serial pin location on your router Note:- Some WNDR4500v2 may not come with pins for serial communications . In such cases, you will have to attach the pins on your own. Go to the location as indicated in Figure1(a), where you will find a connection with the name J252 as shown in Figure 1(b). Solder the pins here carefully. Figure1(b): Serial pin location on your router Identify important pins on router for serial communication: Important pins on the router for serial communication are identified in Figure 2. Figure 2: Important pins on the router for serial communication Identify important pins in USB-TTL cable: Important pins in the USB-TTL cable are indicated in Figure 3. Figure...
Developers, they’re what makes the technology world go ’round' and they’re what’s help make NETGEAR open routers the most customized routers on the planet. Without the amazing developer community – from indie devs plucking away keys in their basement to the advanced developers writing line after line – NETGEAR custom firmware would be nothing without them. And let’s not forget the amazing testing and modding community. This invite goes to firmware developers. If you’re one of them, thanks for everything you’ve done! We can only reward two developers with a new R7000 router but we hope in some small way this illustrates our appreciation to the development community. If you have a particular fondness for a developer contact them and ask them to fill out our survey How to Enter It could not be much easier. Just go to our Survey and fill it out. You will automatically be entered. (hint.... enter as much information you can in part #7, the essay, about what you plan to do with the router if you win one)
Introducing: DD-WRT for the NETGEAR EX6200. [Download DD-WRT for NETGEAR EX6200 at MyOpenRouter] The EX6200 is naturally a Wifi Range Extender -- now, it gets a special upgrade using DD-WRT open source firmware. DD-WRT will transform this Range Extender into a full featured Wifi Router. By default, the EX6200 has 5 LAN ports and no WAN port. DD-WRT allows you to use one of the LAN ports as a WAN port + 4 LAN ports. Since there are differences in features, I'm going to explain a few of the changes when using it with DD-WRT. In the picture below you can see that once you have flashed DD-WRT, you will have one WAN port, which is port 5 on the router. The LED with label "Connected" will show WAN status, once it lights up you are connected to WAN either through a cable connection or wifi connection, e.g. Client Bridge. The wifi lights will only display if the radio is online or offline. NETGEAR logo is used as diag light indicating DD-WRT diag events, e.g. if you press Save or Apply in the web, this light will confirm this action. The WPS button on the back is being used as...
Announcing the new R8000 AC3200 Nighthawk X6 Tri-Band WiFi Router! Connecting the Internet to Everything T here's never been WiFi like it. The Nighthawk X6 AC3200 Router with breakthrough Tri-Band WiFi technology was built to connect to each and every device in your home??automatically and simultaneously. Laptops, tablets, phones, TVs, game consoles, music streamers, cameras ?? if it??s WiFi enabled, it??s X6 accelerated. With a massive combined wireless speed of up to 3.2Gbps, 3 WiFi bands and Smart Connect intelligence, every device is assigned the fastest WiFi connection possible and optimized for maximum speed. Multiply your WiFi Nighthawk X6 takes your WiFi experience to another level with Tri-Band WiFi and 6 high-performance antennas. Check out the Video! More WiFi for More Devices See the eye-opening, multiple-device-connecting prowess of the Nighthawk X6??with speeds up to 3.2Gbps and a 1 GHz dual core processor with 3 offload processors. R8000 WiFi Technology 802.11ac Tri-Band Gigabit Speed and Range WiFi Performance AC3200 (600 + 1300 + 1300 Mbps)? WiFi Range Very large homes WiFi Band Simultaneous Tri-Band WiFi - Tx/Rx 3x3 (2.4GHz) + 3x3 (5GHz) + 3x3 (5GHz) Beamforming Beamforming+??Smart, signal-focusing technology boosts the speed,reliability, and range of your WiFi connections Number of Ethernet...
SAN JOSE, Calif. — July 14, 2014 — NETGEAR®, Inc. (NASDAQ: NTGR) ( www.netgear.com ), a global networking company that delivers innovative products to businesses, consumers and service providers, today announced ReadyRECOVER™ ( www.netgear.com/readyrecover ), a new addition to their innovative ReadyDATA™ unified storage (NAS/SAN) platform. ReadyRECOVER is a backup appliance built to run exclusively with the ReadyDATA family of storage appliances. With ReadyRECOVER, small and medium-sized businesses (SMBs) are able to create full backups of servers, desktops and laptops every 15 minutes that can be independently used to quickly and reliably restore files, folders, databases or systems to any platform, physical or virtual. For the first time, businesses can confidently back up their data forever, without ever needing inefficient and time-consuming periodic full system backups. NETGEAR is the first technology provider to enable incremental backups as full restore points delivering extremely simple recovery point management. ReadyRECOVER integration of the ReadyDATA storage appliance with award-winning ShadowProtect® backup and disaster recovery software from StorageCraft® Technology Corporation ( www.storagecraft.com ) results in each incremental snapshot functioning as a full recovery point, but consuming a minimal amount of storage space. In addition, each snapshot captures the entire system, the Microsoft Windows® OS, and...
Introduction: Using serial console setup users can get access to the serial console of their router. Serial console setup finds its most important use in debricking a router. Moreover, developers may use it to extract useful debug information from their routers. This short tutorial explains how to setup serial console for Netgear R8000. Identify location of Serial pins on your router: First open the case of your router. You should be able to find pins for serial communications at the location indicated in Figure1(a). Figure1(a): Serial pin location on your router Note:- Some R8000 router may not come with pins for serial communications. In such cases, you will have to attach the pins on your own. Go to the location as indicated in Figure1(a), where you will find a connection with the name J252 as shown in Figure 1(b). Solder the pins here carefully. Figure1(b): Serial pin location on your router Identify important pins on router for serial communication: Important pins on the router for serial communication are identified in Figure 2. Figure 2: Important pins on the router for serial communication Identify important pins in USB-TTL cable: Important pins in the USB-TTL cable are indicated in Figure 3. Figure...
This article describes the steps required for firmware upgrade in Netgear R8000. Here I use OEM firmware downloaded from the NETGEAR support site and DD-WRT firmware downloaded from here . Step1: Log in to the router web interface i.e. 192.168.1.1 and navigate to the Advanced -> Administration ->Backup Settings as shown in figure 1. Figure 1 Step2: Click the “Erase” button under “Revert to factory default settings” section as shown in figure 2. Figure 2 Step 3: Click the “Yes” button as shown in figure 3. Figure 3 The router will reboot and you will be able to see a page same as figure 4. Wait for the reboot process to complete. Figure 4 Step 4: Log in to the router web interface i.e. 192.168.1.1 and navigate to the Advanced ->Administration->Router Update as shown in figure 5. Figure 5 Step 5: Click “Browse”, select the path for the DD-WRT firmware that you downloaded and click on the “Upload” button as shown in the figure 6. Figure 6 Step 6: Then click on the “OK” button as shown in figure 7. Figure 7 The router will reboot and you will be able to see a page same as figure 8. Wait...
I've been a long time fan of NETGEAR routers, and with the R8000, they've really upped their game. There's a lot of hype about this particular router; many tout it as one of the best, if not the best on the market... and it certainly looks the part. However, with use by an average household, is it really worth it? Does it measure up? Unboxing the NETGEAR R8000 I won't bore you with too many details here -- unboxings are cliche, no? I do really dig them, though, so here's some pics of what it's like to open one up. The packaging is top notch and very blingy, and this router really has a distinctive look. Gold, shiny packaging. The router of the hour. Anatomy of the NETGEAR R8000 The R8000 is a beast of a router. Sporting looks like a geeky Lamborghini Diablo with antennae, nobody is going to mistake this for any other product. It's about a foot wide and 9 inches deep. So yeah, it's got a presence. Whoa, what's this? 2 antennas not enough for you? How about 4? Still not enough? Well, here's no less than SIX antennas sprouting from this monster. The entire top...
